Freight density calculator
Enter outside dimensions and weight, including the pallet and packaging.
Sample class uses the standard density scale. Your commodity’s NMFC rules may give a different class. See an example
Bring your LTL workflow into Albatross.
We're inviting small and midsize shippers to try Albatross and help shape the integrations and workflows they need.
Measuring your freight
Measure from the bottom of the pallet to the highest point of the load. Include overhang in the length and width, and use the weight of the complete unit.
Density is weight divided by volume:
Volume (ft³) = length × width × height (in) ÷ 1,728
Density (lb/ft³) = weight (lb) ÷ volume (ft³)
How height changes density
Both pallets below weigh 450 lb and have a 48 × 40 in footprint. Doubling the height halves the density.
Why density alone doesn't give you a freight class
An NMFC item identifies a commodity and its classification rules. Freight class comes from those rules. When the item uses density ranges, your PCF result helps you find the applicable class.
Two loads with the same density can have different classes if their commodities have different requirements.
- Density
- The weight relative to the space the load occupies.
- Handling
- The equipment or care needed to move it.
- Stowability
- How it fits with other freight in a trailer.
- Liability
- The risk of damage, theft, or damage to other freight.
Same size, same weight, different class
Both loads: 48 × 40 × 45 in450 lb50 ft³9 lb/ft³
| Freight | Applicable provision at 9 lb/ft³ | Class |
|---|---|---|
| Boxed optical lenses NMFC item 57810 | 8 to less than 10 lb/ft³ | 100 |
| Packaged conveyor parts NMFC item 120700 | 8 to less than 15 lb/ft³, with no dimension over 96 in | 92.5 |
The standard density scale suggests class 100 for both. The conveyor parts' commodity rules give class 92.5.
Illustrative loads. Published NMFTA rules: optical lenses (opens in a new tab) and conveyor parts (opens in a new tab) . Check current item descriptions, packaging, notes, and effective dates before booking.
Common questions
Do I include the pallet's weight and dimensions?
Yes. Enter the weight of the entire loaded pallet, including the pallet, cartons, wrap, and other packaging. Measure the finished unit from its outermost edges.
Where do I measure the height?
Measure from the floor or bottom of the pallet to the highest point of the load. The height of the cartons alone leaves out the pallet and understates the space your freight occupies.
What if my freight hangs over the pallet?
Include the overhang. A 48-inch pallet carrying cartons that extend 2 inches beyond each end has a loaded length of 52 inches. Measure the loaded width the same way.
How do I measure irregular freight?
Use the greatest outside length, width, and height, including packaging and anything that protrudes. Calculate the rectangular space enclosing the entire unit; do not subtract gaps, curved edges, or empty space between pieces.
Do I enter the weight of one pallet or the whole group?
Enter the weight of one loaded pallet in Weight each. Quantity multiplies that weight and volume for shipment totals. For three identical 450 lb pallets, enter quantity 3 and weight 450, not 1,350.
How do I calculate density for different-sized pallets?
Add a pallet group whenever dimensions or weight differ. Use quantity only for identical pallets. Calculate each group's density separately; a shipment average can hide a lighter, less dense pallet.
Why do you divide the dimensions by 1,728?
The dimensions are in inches, so multiplying them gives cubic inches. One cubic foot contains 12 × 12 × 12 = 1,728 cubic inches. A 48 × 40 × 45 inch load occupies 50 cubic feet; at 450 lb, its density is 9 lb/ft³.
Should I round my measurements?
Enter your measured dimensions and weight as accurately as you can; decimals are supported. Do not round down or leave out packaging. Follow your carrier's measurement and rounding rules when preparing the shipment.
Will stacking cartons more tightly increase density?
If the total weight stays the same and the finished load occupies less space, its density increases. Reducing a 450 lb load from 48 × 40 × 90 inches to 48 × 40 × 45 inches increases density from 4.5 to 9 lb/ft³. Keep the load stable and follow its packaging requirements.
Why might the carrier calculate a different density?
Compare the carrier's measured dimensions and weight with yours. Overhang, bulging wrap, an omitted pallet height, or an estimated weight can change the result. Keep a record of the finished load's measurements and weight so you can compare them with any remeasurement.
Sources: NMFTA classification guidance (opens in a new tab) and density guidance (opens in a new tab) .
Albatross · tryalbatross.com/tools/freight-density-calculator
Density is per handling unit. Confirm each commodity’s NMFC item and provisions before shipping.